Artificial Turf · Installation

How to Install Artificial Turf - Base, Drainage, Seams and Edges

Ask any installer why a synthetic lawn failed and the answer is nearly always underneath it. Rolling out the turf takes an afternoon. Digging out the old lawn, building a compacted stone base and making sure water and pet urine can drain away is what keeps it flat, dry and odor-free for the next decade. Here is the whole job in order, with the details that make the difference.

General guidance for US yards. Call 811 a few days before you dig so buried utility lines are marked, keep clear of large tree roots, check HOA rules before you start, and get professional advice for rooftops and balconies where weight and waterproofing matter. Part of the PlantMapper Artificial Turf section.

A plate compactor being used to firm up the ground during site preparation
Compacting the base in thin lifts is the real work · photograph via Pexels
Before you start

This is a grading job that ends in green

Think of a turf install as light earthwork, not carpet laying. You dig out 3 to 4 inches of soil across the whole yard, haul it away, bring in and compact a similar amount of crushed stone, and only then unroll the part everyone pictures. Most of the cost and almost all of the lifespan is in that groundwork.

Three things decide how it turns out: compaction (a loose base sinks into dips after the first wet season or freeze-thaw cycle), drainage (water and dog urine that sit under the backing turn into soggy patches and smells), and a solid perimeter for the edges to be nailed into. Everything below is detail hung on those three.

Be honest about size. Around 200 sq ft is a doable DIY weekend for two people with a rented compactor and a small dumpster. At 600 sq ft you are moving several dump-truck loads of soil and stone, and most homeowners are better off getting two or three quotes from installers.

Before any digging, check two things. First, HOA rules: many associations want to approve turf color, pile height and edging, and some have tried to ban it outright. A number of states and cities, particularly in drought-prone parts of the West, now limit how far an HOA can ban water-wise landscaping, so check your state's rules and your HOA's current guidelines. Second, rebates: some water utilities pay for removing thirsty lawn, but many of them now exclude synthetic turf and only pay for living, water-wise plantings. Read the program terms before you rip anything out.

What you need

Tools and materials

✓Tools

  • Sod cutter (rented) for anything bigger than about 200 sq ft - a flat spade for smaller jobs
  • Shovels, a landscape rake and a wheelbarrow, plus far more trips than you planned
  • Plate compactor (rented), very roughly $80-150 a day from a rental yard or home improvement store. Not optional
  • A 4 ft or 6 ft level, a long straightedge and mason's line
  • Utility knife with a big pack of blades - turf backing dulls them quickly
  • Carpet kicker or a power stretcher for working out wrinkles, and a stiff push broom or power broom for the infill
  • Cordless drill and a hammer for the perimeter boards and nails
  • Kneeling boards so you are not leaving knee prints in the base you just screeded
  • Gloves, safety glasses, hearing protection and a dust mask for cutting stone dust and running the compactor

!Materials

  • Artificial turf in full roll widths, plus about 4 in extra on every side
  • Crushed stone road base (3/4-inch minus, class II road base or similar) - roughly 1 cubic yard for every 100 sq ft at 3 in deep
  • Decomposed granite or stone dust for the top leveling layer, about 1/2 to 1 in
  • Permeable woven landscape fabric if your turf maker calls for it, enough to overlap about 6 in at seams
  • Bender board or pressure-treated 2x4s (or steel edging) for the perimeter
  • Galvanized landscape staples or turf nails, typically 5 to 6 in long
  • Seaming tape and turf adhesive, or self-adhesive seam tape
  • Infill - silica sand, coated sand or another type, at the manufacturer's rate (often 1 to 2 lb per sq ft)
  • A roll-off dumpster, or a plan for hauling away several tons of sod and soil
Step one

Measuring and planning the layout

Good planning saves real money here, because you cannot turn a piece sideways to make it fit without the grain showing.

  1. Measure at the widest and longest points

    Use the maximum width and the maximum length, not an average, then add about 4 in on every side for trimming. Draw the shape on graph paper with the real measurements written on it.

  2. Find out the roll width first

    Most residential turf in the US comes in 15 ft wide rolls, and some lines also come in 12 ft. A 20 x 20 ft yard from 15 ft stock needs a 15 x 20 ft piece plus a 5 x 20 ft strip and one seam. Sometimes a different width wastes much less; sometimes it adds a seam. Price both before ordering.

  3. Pick a grain direction and stick to it

    Every piece must have its fibers leaning the same way, or the pieces will look like two different shades of green. Point the grain toward the main viewing spot - usually the back door, the patio or the deck - because turf looks fullest when you are looking into the lean of the fibers.

  4. Put seams where nobody looks

    Keep them away from the back door and the seating area, and run them away from the viewer rather than across the line of sight where you can. A seam under the play set or along a shady side vanishes; one across the middle of the lawn does not.

  5. Plan around obstacles

    Trees, sprinkler valve boxes, cleanouts, clothesline posts and walkways all need cutting around, and each one creates offcuts. Valve boxes and sewer cleanouts must stay reachable - cut a neat flap, or set a lid with turf glued to it.

  6. Order full widths and expect waste

    Waste of 15 to 30 percent is normal on anything that is not a plain rectangle. Keep the biggest offcuts; they are what you will patch with years from now.

The cheapest design decision you will make. If the area you want is 16 ft wide and the roll is 15 ft, that extra foot means a second strip, a seam and more turf. Pulling the lawn in to 15 ft and running a 1 ft band of gravel, river rock or low planting along one side is cheaper, faster and usually looks better. Design to the roll width whenever you can.

Step two

Removing the existing lawn

All the organic material has to go. Sod or roots left in place break down over a few years and the turf above them sinks into soft spots.

  1. Call 811 and check what else is buried

    Call 811 (or use your state's online request) a few business days ahead so public utility lines are marked for free. Private lines are not covered, so also find your irrigation pipes and valves, landscape lighting cable, any wire to a shed and any drain lines. You are digging over the whole area, not one trench.

  2. Deal with the irrigation

    Cap or remove sprinkler heads in the area, or convert the zone to drip for any surrounding beds. A forgotten pop-up head under new turf will either push up a bump or flood the base.

  3. Kill or dig out tough perennial weeds

    Bermudagrass, nutsedge, field bindweed, quackgrass and dandelions will find their way through fabric, seams and edges. Get them properly dealt with first; rushing this step comes back to haunt you.

  4. Dig down to depth

    Remove sod, topsoil and roots to about 3 to 4 in below the finished level you want (more on soft or wet ground). The finished level is the top of the turf fibers, so work backward through pile height, the leveling layer and the base.

  5. Haul the soil off site

    A 400 sq ft lawn dug 4 in deep produces about 5 cubic yards of sod and soil, which is several tons. Book the dumpster before you start and keep a clear path to it.

  6. Loosen any hardpan, then compact the subgrade

    If the exposed soil is a hard, slick crust - common under old lawns and on new-build lots - break it up so water can soak through, then give the whole subgrade two or three passes with the compactor before any stone goes in. Skipping this is the usual reason a lawn develops dips in its first year.

Step three

The base - the part that decides everything

Two layers of stone, each compacted. This is most of the labor and all of the longevity.

Typical base build-up for residential artificial turf. Depths are compacted depths; follow your turf maker's spec where it differs.
LayerMaterialDepthWhat it does
SubgradeThe native soil you dug down to-Compacted before anything goes on it; broken up first if it is hardpan
BaseCrushed stone road base (3/4-inch minus, class II) or crushed graniteAbout 3 in for typical yards; 4 in or more on soft clay, wet ground or where a vehicle may crossSpreads the load, stops settling and lets water through
Leveling layerDecomposed granite, stone dust or fine crushed rockAbout 1/2 to 1 inA smooth, screeded bed that makes the finished lawn flat
Fabric (often optional)Permeable woven landscape fabric-Under the turf where the maker recommends it, overlapped about 6 in at seams
Pad (optional)Permeable foam shock padAbout 3/8 to 1 inUnder play equipment, over concrete or on a rooftop
TurfThe synthetic turfAbout 3/4 to 1 1/2 in pileSeamed and nailed along the perimeter
  1. Spread the base in lifts, never all at once

    Wheel it in and rake it out about 2 in at a time, compacting each lift before the next. Trying to compact 4 in in one go leaves the bottom loose, and it settles later.

  2. Dampen it and compact properly

    Mist the road base with a hose so it binds, then make three or four passes with the plate compactor in different directions on every lift. When you can walk on it without leaving footprints, it is done.

  3. Build in a gentle slope if you can

    A fall of about 1 in per 8 to 10 ft away from the house helps heavy rain run off. Permeable turf drains straight down, so a slope is not essential, but it costs nothing to add and keeps water away from the foundation.

  4. Screed the leveling layer

    Rake out decomposed granite or stone dust, pull a straight board across screed rails to level it, then compact it lightly. This is the surface you feel underfoot, and every dip left here shows in the finished lawn.

  5. Check with a straightedge and level

    Drag a 6 ft straightedge across in both directions. Fill low spots, mist and compact again. This is the last time it is easy to fix.

  6. Add fabric last, if you are using it

    Many installers in dry climates skip fabric over a well-compacted base; others use it where weeds are bad. If you use it, choose a permeable woven grade, overlap about 6 in, run it up to the perimeter boards and staple it down.

Water

Drainage

Quality turf on a permeable base drains faster than real grass. Trouble comes from the soil underneath, or from laying it on something that cannot drain at all.

Average soil

Let the base do the work

On ground that already drains reasonably well, a compacted, permeable stone base is enough. Water runs through the turf, through the leveling layer and into the soil.

  • Use crushed road base and decomposed granite, both of which stay permeable when compacted
  • Avoid stabilized or cement-mixed DG under turf unless you are also adding drains
  • A gentle slope away from the house helps in downpours

Heavy clay or soggy ground

Fix it before you build

Turf over ground that holds water gives you a wet lawn you cannot see into, and with dogs that is exactly where the smell starts.

  • Sort the drainage first - see Yard Drainage
  • Consider a French drain along the low side, taken to a dry well or a safe outlet
  • Deepen the base to 4 to 6 in of clean, open crushed stone
  • Never just cover it and hope for the best

Over concrete or pavers

Only if water can get away

Turf over an old slab, patio or pool deck is common and works well, as long as the water has an exit.

  • Check the slab slopes to an open edge or a drain
  • Use a permeable foam pad or drainage mat rather than gluing turf straight to concrete
  • Drill drain holes in the slab if water has nowhere else to go
  • Keep the finished surface well below the siding and any weep holes or weep screed on the house

Homes with dogs

Drainage is odor control

Urine passes straight through a fully permeable backing, but then it has to keep moving. If it stalls at the leveling layer, it stays there and smells.

  • Choose a pet turf with a fully permeable backing, not just punched drain holes
  • Keep the leveling layer thin and use clean crushed rock where drainage is slow
  • Avoid very fine material that clogs, and consider zeolite infill to hold ammonia odor
  • Plan a rinse routine - see Maintenance
Step four

The perimeter and edges

The turf has to be nailed into something solid all the way around, or the edges curl up, lift and trip people. Decide on the edge before the base goes in, because the boards are set at base height.

✓Ways to finish an edge

  • Bender board or pressure-treated 2x4s, staked around the edge with the top level with the finished base. The usual and cheapest answer; the turf is nailed into it.
  • Against a patio, walkway or driveway - the easiest edge of all. Set the base so the turf finishes flush with the hard surface, then glue the last few inches down.
  • Steel or aluminum landscape edging, which gives a crisp, permanent line to fix into. See Edging Materials.
  • Landscape timbers, pavers or a concrete mow curb, which also hold the base where the ground drops away.
  • Tucked into a trench - the turf edge folded down a few inches into a gravel-filled trench and staked. Invisible, and good next to planting beds.

!Edge details that matter

  • Nail every 4 to 6 in along the whole perimeter with galvanized nails or staples.
  • Cut from the back, along a stitch row, never from the fiber side. The edge comes out far cleaner.
  • Leave the turf a little long and trim in place rather than cutting it to size first.
  • Next to a flower bed, let plants spill over the edge - a hard visible line is what gives turf away as fake.
  • Around trees, cut a generous ring and finish it with mulch or gravel; never butt turf against the trunk.
  • Never leave any edge unfastened, however short. It will lift within a season.
Step five

Rolling out the turf

The fun part, and fast - but do one thing before anything else.

  1. Let it relax

    Unroll the turf and leave it lying flat, in the sun if you can, for a few hours before cutting. It arrives tightly rolled and remembers it; cut straight off the roll, it ripples and shrinks back later. On a cool day, give it longer. In hot weather, wear gloves - turf fibers and backing heat up fast in full sun.

  2. Check the grain on every piece

    Run your hand across each piece. All of them must lean the same way, toward the main viewing spot. Two pieces laid in opposite directions look like two different products, and there is no fixing it afterward.

  3. Dry-fit everything before you cut

    Drag all the pieces roughly into place, overlapping where they will seam, and check the whole area is covered with spare to trim. Only then pick up the knife.

  4. Cut from the back

    Flip the edge over and cut along a stitch row with a sharp blade, changing blades often. Cutting from the top gives a ragged edge and slices fibers you wanted to keep.

  5. Work it flat

    Smooth from the middle outward, pushing out any wrinkles. A carpet kicker helps. You are taking up slack, not stretching it drum-tight.

  6. Nail the perimeter last

    Once everything is positioned, seamed and flat, nail or staple all the way around every 4 to 6 in, into the boards or the edge of the hard surface.

The skilled part

Making a seam disappear

A good seam is invisible; a bad one is the first thing visitors notice. It is not hard, but it rewards patience.

  1. Cut off the factory edge on both pieces

    Trim away the factory edge strip - usually a little over 1/2 in - from both pieces, cutting from the back along a stitch row. Both cuts must be dead straight or the seam will show as a wavy line.

  2. Butt the edges, never overlap

    Bring the pieces together so the backings just touch, with no more than about 1/8 in gap. An overlap leaves a permanent ridge; a wider gap leaves a visible part line.

  3. Dry-check the grain and the fit

    Both pieces leaning the same way, and the seam lying flat with nothing pulling it apart. Adjust now, because the adhesive does not forgive.

  4. Fold both edges back and lay the tape

    Fold back about a foot of each piece. Center the seaming tape along the line, shiny side down, so it sits equally under both edges.

  5. Glue in a zigzag, or use self-adhesive tape

    Run a continuous zigzag bead of adhesive along the tape, then lay the first edge down and the second tight against it. With peel-and-stick tape, peel the backing a section at a time rather than all at once.

  6. Keep fibers out of the glue

    As each edge goes down, push the fibers away from the seam with your fingers. Fibers glued flat into a seam are what make it visible forever.

  7. Weight it and leave it

    Press the seam down along its full length and weight it with boards or bags of infill for as long as the adhesive label says - usually a few hours. Stay off it while it cures.

The seam test. Once cured, brush across the seam with a stiff broom and step back about 15 ft. A good seam vanishes. If you still see a line, it is nearly always one of three things: the cuts were not straight, fibers are trapped in the glue, or the grain runs opposite ways. The first two can be improved; the third cannot.

Seaming kit

Amazon picks

As an Amazon Associate, PlantMapper may earn from qualifying purchases. Prices and availability are set by Amazon. Give the turf a few hours to relax before cutting, and lay every piece with the grain running the same way.

Step six

Infill and finishing

The last hour of the job, and it changes how the lawn looks, feels and wears.

  1. Choose the infill to suit the yard

    Silica sand is the cheap, common choice for weight and support. Coated (acrylic-coated) sand is rounder and cleaner and is popular for pet areas. Zeolite is a mineral that traps ammonia and is used in dog runs. Organic infills such as cork, walnut shell or coconut fiber are marketed as running cooler but can break down, float or blow around. Crumb rubber is mainly a sports-field infill and is less common in backyards. Use what your turf maker specifies, at their rate.

  2. Brush the fibers up first

    Go over the whole lawn against the grain with a stiff push broom or a power broom. This lifts fibers that were flattened in the roll and by your boots.

  3. Spread the infill evenly

    Use the rate on the spec sheet (often roughly 1 to 2 lb per sq ft for sand), in two or three light passes rather than piles. A drop spreader makes a big lawn easy, and the infill must be dry or it clumps.

  4. Brush it all the way down

    Work it into the backing, brushing in several directions. The infill should vanish into the fibers; if you can still see it on top, keep brushing.

  5. Brush the fibers up again and tidy the edges

    A final pass against the grain stands everything back up. Then walk the perimeter for fibers tucked under the edge, any loose section and any nail heads standing proud.

  6. Save the offcuts

    Roll the biggest pieces and store them out of the sun in the garage or a shed. Years from now they are the only thing that will patch a burn or tear with turf that has weathered to the same color.

Putting it together

The build, in order

For a simple rectangle of about 250 sq ft on decent soil. Two weekends for two people with a rented compactor is a fair estimate; in hot climates, start early and stop in the afternoon heat.

  1. The week before: call 811, check HOA, plan and order

    Get utilities marked, confirm any HOA approval, mark out the area, plan the roll layout and grain direction, and book the dumpster, the compactor and the stone delivery.

  2. Weekend one, morning: strip the lawn

    Sod cutter or spade, taking out sod, topsoil and roots to 3 to 4 in below the finished level. Wheel the soil straight to the dumpster.

  3. Weekend one, afternoon: subgrade, irrigation and perimeter

    Cap the sprinklers, loosen any hardpan, compact the subgrade, then stake the bender board or treated boards around the edge at the right height.

  4. Weekend two, morning: the base

    Crushed road base in lifts of about 2 in, dampened and compacted with three or four passes each, sloping gently away from the house.

  5. Weekend two, midday: leveling layer and fabric

    Decomposed granite or stone dust screeded about 1/2 to 1 in deep and compacted, checked with a straightedge, then fabric overlapped and stapled if you are using it.

  6. Weekend two, lunchtime: unroll and relax the turf

    Roll it out and leave it flat for a few hours while you eat. Do not skip this.

  7. Weekend two, afternoon: cut, seam, nail and infill

    Position, trim from the back, seam with tape and adhesive, nail the perimeter every 4 to 6 in, then brush, add infill and brush again.

On the job

The installation checklist

Fifteen checks from start to finish. Your ticks are saved in this browser only.

Planning and digging

Base and perimeter

Turf

Installation questions

Installing artificial turf: frequently asked questions

How deep should the base be for artificial turf?

For a typical backyard, about 3 in of compacted crushed stone road base (3/4-inch minus or class II) topped with roughly 1/2 to 1 in of decomposed granite or stone dust, which means digging out about 3 to 4 in below the finished level. Soft clay, wet ground or areas a vehicle might cross need more, often 4 to 6 in of base. What matters most is compacting it in thin lifts of about 2 in rather than all at once.

Can I put artificial turf directly on dirt?

You can, and it is the most common reason installs fail. Soil settles unevenly and holds water, and any sod or roots left underneath rot over a few years and leave dips. Weeds also come straight up through it. A compacted stone base is what keeps the surface flat and draining, and it is most of the cost and most of the value of the job.

Do I need landscape fabric under artificial turf?

It depends on the product and the site. Many installers in dry climates skip it over a well-compacted base, while others add a permeable woven fabric where weeds are a problem. If you use it, it goes on top of the leveling layer, directly under the turf, overlapped about 6 in at seams. It only stops weeds from below; most weeds in turf actually grow from seed that blows onto the surface.

How do you seam artificial turf so it doesn't show?

Cut the factory edge off both pieces from the back along a stitch row so both cuts are perfectly straight, then butt the backings together with no more than about 1/8 in gap - never overlap them. Fold both edges back, center seaming tape along the line, run adhesive in a zigzag, and push the fibers away from the seam as you lay each edge down so none get glued flat. Weight it and let it cure.

Which way should the turf grain face?

Toward the spot you look at it from most, usually the back door, patio or deck, because turf looks fullest when you are looking into the lean of the fibers. More important still, every piece must run the same way: two pieces with opposite grain look like two different colors in sunlight, and you cannot fix it once they are down.

How long should artificial turf sit before cutting?

A few hours unrolled and lying flat, and longer on a cool day or if it has been stored tightly rolled. It remembers the curl of the roll, and turf cut and nailed straight away tends to ripple and shrink back later. Rolling it out in the sun before a lunch break is the easiest way to build the wait into the day.

What infill should I use for artificial turf?

Most turf needs infill brushed into the fibers to weigh it down, hold the blades upright and protect the backing from UV. Silica sand is the budget standard; coated sand is cleaner and popular with pet owners; zeolite is added in dog areas to trap ammonia odor; organic infills such as cork or walnut shell are sold as cooler options but can break down or wash about; crumb rubber is mostly used on sports fields. Use your turf maker's recommended type and rate, often roughly 1 to 2 lb per sq ft for sand.

Can artificial turf be installed over concrete or a patio?

Yes, as long as water can escape. Check the slab slopes to an open edge or a drain, and lay a permeable foam pad or drainage mat rather than gluing turf straight to the concrete, or you have built a tray. A flat slab with no way out may need drain holes drilled. Keep the finished surface well below the house siding and any weep holes.

Do I need HOA approval to install artificial turf?

If you live in an HOA, assume yes until you have checked. Many associations have rules on turf color, pile height, edging and where it can go, and some have banned it. Several states and cities, especially in drought-prone areas, have passed rules limiting HOA bans on water-wise landscaping, and some of those cover synthetic turf, but the details vary. Read your HOA guidelines, check your state's current rules and get written approval before you start.

Does artificial turf get hot?

Yes. In strong summer sun, especially in the Southwest, the surface gets much hotter than natural grass and can be uncomfortable for bare feet and pets' paws. Shade from trees or a shade sail helps most, a quick hose-down cools it temporarily, and lighter-colored or heat-reducing fibers and some infills help a little. Plan shaded play areas if children or dogs will use it on summer afternoons.

Where to go from here

Next steps