How you hold the water (flexible liner, rigid preformed shell or an all-in-one basin kit) sets the shape you can have, the price and the lifespan. How much gear you add sets how much upkeep you sign up for, and there is a strong case for buying as little of it as you can.
Pumps, lights and all electrical gear must be rated for outdoor and submersible use. Plug only into a GFCI-protected outdoor outlet with a weatherproof in-use cover, and have any new circuit, outlet or buried cable installed by a licensed electrician to the electrical code your area enforces, often with a permit. Unplug before your hands go in the water. Open water is also a serious drowning risk for young children; see safety. Part of the PlantMapper Water Features section.
Buy as little equipment as the feature can get by with · photograph via Pexels
How to choose
Two decisions, and one of them is about holding back
First, how the water is held: a flexible liner you shape to your hole, a rigid preformed shell you set in the ground, or a sealed all-in-one kit with a hidden basin. Shape, size and cost all follow from that.
Second, how much equipment to buy, and the urge to overbuy is strong and usually wrong. A planted wildlife pond with no fish needs no pump, filter, UV clarifier or electricity at all. A fountain needs a pump. Only a pond with a real fish load truly needs filtration.
Every piece of gear you add is a purchase, an electric bill, a maintenance job and something that can fail in the middle of a heat wave or a hard freeze. The best backyard water features tend to have the least equipment in them.
The main choice
Flexible liner, preformed shell or basin kit
Three ways to hold water, each with very different strengths.
Pond and water feature building methods compared. Costs are rough US ranges and vary by region.
Flexible liner
Preformed shell
Self-contained kit
What it is
A sheet of EPDM rubber (or RPE or PVC) over underlayment, shaped to the hole
A molded rigid pond, usually fiberglass or polyethylene
A pump, a covered basin and an ornament such as a bubbling rock or urn
Shape
Any shape and any size you can dig
Fixed: whatever the mold gives you
Fixed, but the feature above it can be almost anything
Typical size
From about 10 sq ft upward, no real limit
Usually 5-30 sq ft
Basin about 1-2 ft across
Life
EPDM 20-30 years or more; cheap PVC 5-10
Fiberglass 20+ years; polyethylene 10-20
Basin indefinitely; pump 3-8 years
Difficulty
Moderate: the digging is the work
Easy to buy, surprisingly fussy to level and backfill
Easiest of the three
Open water
Yes
Yes
No: the basin is covered
Best for
Wildlife ponds of any size, natural or formal
A small pond fast, or the top pool of a waterfall
Sound and sparkle with no pond, and where kids play
Rough cost, about 40 sq ft
About $250-$700 in materials
About $200-$500
About $150-$600
✓Why a flexible liner usually wins
Any shape and size, including the sloping beach and varied depth a wildlife pond needs.
45 mil EPDM lasts decades, stays flexible in cold weather and can be patched.
Cheaper per square foot than a preformed shell once you go beyond a small pond.
Easy to hide: sod, soil, river rock or coping can be brought right to the water.
Forgiving of a hole that is not exactly to plan.
The standard for nearly every good backyard pond in the US.
!When a preformed shell makes sense
You want a small pond quickly with few decisions.
As the top pool of a waterfall, where a rigid shape helps.
Very rocky or root-filled ground where the risk of puncture is high.
A raised pond built inside a timber or block wall.
Be warned: they are much harder to install well than they look. The hole must closely match the shape and the backfill must be tamped in stages, or the shell warps.
The plant shelves on most preformed ponds are narrow, which limits what you can grow.
Getting the liner right
Liner types, underlayment and sizing
The liner is the one part not to cheap out on, because replacing it means draining and rebuilding the whole pond.
Which liner to buy
45 mil EPDM rubber: the standard US pond liner. Durable, flexible even in cold weather, easy to fold into corners and repairable. Lasts decades. The safe choice.
Fish-safe vs roofing EPDM: make sure the EPDM is sold as pond-grade or fish-safe. Roofing EPDM may contain additives that are toxic to fish and wildlife.
RPE (reinforced polyethylene): thinner and much lighter than EPDM for the same strength, handy for big ponds and for carrying to the site, but stiffer to fold. PVC: cheaper and shorter-lived, and it gets brittle in strong sun. Fine for a small or temporary pond.
Thin "pond liner" off a store roll: usually the shortest-lived of all. Fine for a container or bog garden, not a pond.
Check the warranty: a good fish-safe EPDM liner typically comes with a 20-year or longer one, which tells you what the maker thinks of it.
Buy one piece big enough for the whole pond. Seams can be made with seam tape, but they are the most common place a pond leaks.
Working out what size to buy
The formula is simple and worth doing carefully, because a liner 4 in short is a disaster and one that is 3 ft over is only money.
Liner length = maximum pond length + (2 × maximum depth) + 2 ft for overlap.
Liner width = maximum pond width + (2 × maximum depth) + 2 ft for overlap.
So a pond 10 ft long, 6 ft wide and 2 ft deep needs a liner of about 16 x 12 ft.
Measure the maximum size of the finished hole, including any beach that extends outward.
Round up to the next size sold. Extra liner is trimmed at the end; a shortfall means starting over.
The water volume calculator works out the gallons you will need to know for pump and treatment sizing.
Underlayment: do not skip it
The most common cause of a leaking pond is a puncture from below, from a rock or root that was in the hole from the start.
Use a proper pond underlayment, a thick non-woven geotextile, over the whole hole, up the sides and over the edges.
Old carpet, sand and newspaper are the classic stand-ins. Sand works on the floor but not the sides; carpet rots and can leach dyes. Real underlayment is cheap and worth it.
Pick every rock and root out of the hole first, and tamp down any soft spots.
On rocky or root-filled ground, use a double layer of underlayment, or sand plus underlayment.
Protect the liner from above too wherever river rock or boulders sit on it, with a second piece of underlayment under the stone.
Keep a liner patch kit with your pond paperwork. Punctures happen years later.
Other ways to hold water
Concrete block with a liner: the standard for a formal or raised pool. The block gives crisp lines and structure; the liner keeps the water in.
Fiberglass coating: a professional finish applied over block or a shell. Durable and neat, but a specialist job.
Sealed containers: a half whiskey barrel, glazed pot or stock tank with the drain hole plugged and sealed, or a small liner inside. The cheapest real water feature there is.
Compacted clay: how farm ponds are often built. It needs the right clay soil, heavy equipment and a lot of space; not a backyard option.
Bentonite: a swelling clay used to seal larger natural ponds. Effective, but a specialist job.
Poured concrete or gunite: durable, but it cracks with frost heave and ground movement, and raises the pH unless sealed. Rarely the best choice now.
The no-pond option
Basin fountains and hidden reservoirs
A basin fountain (often sold as a pondless or disappearing fountain) is a pump in a covered underground basin feeding something above it. It is the safest, simplest and most reliable kind of water feature, and deserves more attention than it gets.
How they work
A basin you never see
A plastic tank or lined pit sits below ground with a pump inside. Water is pumped up through a bubbling rock, urn, sphere or column, spills over, and drains back through a grate covered with river rock.
No open standing water: the grate takes the weight and the stones hide it.
Basins are commonly about 1-2 ft across and about as deep.
Sold as complete kits, or built from a basin, a grate, a pump and an ornament you choose.
The only routine jobs are topping up and a yearly clean.
Getting one to work well
Four details that matter
Basin fountains are simple, but they fail in the same few ways.
Size the basin generously. A small one can run dry in days in a hot, dry summer, and the pump burns out.
Make the grate strong and fully supported; someone will stand on it.
Keep the pump reachable: you must be able to lift the stones and grate to get to it.
Set it up so splash lands back on the stones, not on the patio or in a bed.
Choosing the ornament
Sound and scale
The ornament is what you look at, and the sound is what you live with. Test both before you commit where you can.
A wide, slow spill over a bubbling rock or sphere gives a gentle burble; a narrow jet gives a splash.
Louder is not better: in a small yard a modest trickle is enough to mask street noise or the neighbor's AC unit.
Scale it to the space: a huge urn on a tiny patio looks awkward.
Natural stone, Corten steel, glazed ceramic and stainless all work; match it to the house and yard.
Why they suit so many American yards
The practical case
For a lot of yards a basin fountain is simply the right answer, and it gets passed over because it is not a pond.
The safe choice where small children live or visit, and less likely to fall under pool-style barrier rules (check locally).
No algae, no filter, no plants to manage, no leaves to net out, and no standing water for mosquitoes.
Works in shade, on a small patio, a balcony or against a wall, and uses less water than a pond in dry climates.
Can be drained and shut down before freezing weather in cold zones, or run year-round in mild ones.
Roughly $200-$900 for a good one, all in (varies by region).
As an Amazon Associate, PlantMapper may earn from qualifying purchases. Prices and availability are set by Amazon. Pumps, lights and equipment must be rated for outdoor and submersible use and plugged into a GFCI-protected outlet; any new circuit or outlet is work for a licensed electrician.
Moving the water
Pumps
You only need a pump where water has to move. Buy the smallest one that does the job: an oversized pump wastes electricity, churns a small pond and makes more noise than anyone wants.
✓Choosing a pump
Flow rate is the key number, in gallons per hour (GPH). Match it to what the feature needs, not just the pond size.
For a fountain or spitter, follow the maker's guidance for the ornament; most small features want roughly 100-500 GPH.
For a waterfall or stream, a common rule of thumb is about 100-150 GPH for every inch of spillway width for a light to moderate sheet of water (more for a heavy flow).
Head height matters as much as flow: a pump loses output the higher it has to lift, so read the flow chart at your lift height, not the headline number.
Match the tubing diameter to the pump outlet and keep the run short and free of tight bends: restrictions cost far more flow than people expect.
Choose a pump with a flow adjuster or valve so you can turn the effect down.
!What to avoid
Buying on the headline GPH and ignoring head height.
An oversized pump in a small pond, which churns the water and stirs up muck.
A pump sitting in silt on the pond floor, which clogs the intake constantly: set it on a brick.
Running a tall fountain in a wildlife pond, where it disturbs surface life for no gain (a gentle bubbler is fine and helps with mosquitoes).
Cheap no-name pumps with no spare parts; the impeller wears out and you will want a replacement.
Forgetting the running cost. A pump running 24/7 uses more electricity over a year than most people expect, so look at the wattage and put a decorative feature on an outdoor timer.
Rough pump guide for home features. Always check the maker's figures for your ornament and lift.
Feature
Typical flow
Notes
Small bubbler or pebble fountain
100-250 GPH
Gentle burble; a flow adjuster is essential
Urn, bubbling rock or sphere
250-500 GPH
A wide, slow spill gives the nicest effect
Wall spout or spitter
250-650 GPH
Adjust to get the flow you want
Small fountain jet in a pond
250-500 GPH
Keep the jet low; wind blows a tall one out of the pond
Waterfall, 12 in spillway
About 1,200-1,800 GPH
For a light to moderate sheet of water
Stream and waterfall
1,500-4,000+ GPH
Depends on width, length and total lift
Filtered fish pond
Whole pond volume about once an hour
More for koi; the filter maker will specify; use a solids-handling pump
Wildlife pond
None
No pump, no filter, no fountain: that is the point
Do you really need one?
Filters, UV clarifiers and when to skip them
This is the section that saves the most money. Filters exist to deal with fish waste. A planted pond without fish does not need one.
✓You do not need a filter if
The pond has no fish. A planted wildlife pond balances itself through plants and natural processes.
It is a basin fountain, wall spout or container feature.
You accept that a natural pond is not crystal clear all year, and it should not be.
You have plenty of plants, including submerged plants and lily pads for shade.
The pond is reasonably large and not in full sun all day, especially in hot-summer zones.
You are willing to wait: a new pond turns green for a few weeks and then settles.
!You probably do need one if
The pond is stocked with fish, and certainly if it holds koi.
You want water clear enough to watch the fish, all season.
The pond is small, in full sun and heavily stocked.
The feature is formal and clear water is part of the design.
You keep a lot of fish in a modest volume, the usual cause of constant problems.
If so, size the filter for both the gallons and the fish load, and follow the maker's guidance rather than guessing.
Know what each piece does
A mechanical filter (often a skimmer box plus pads) traps solids such as leaves, silt and waste on foam or mats that you rinse now and then.
A biological filter holds bacteria that turn fish waste into less harmful compounds. It takes weeks to mature and must never dry out or be rinsed in chlorinated tap water, which kills the bacteria.
A UV clarifier does not filter anything: it makes free-floating algae clump together so the mechanical filter can catch it. It is what clears green water, and it is useless without a filter after it.
Run it all the time if you run it at all
A biological filter needs steady flow to keep its bacteria alive. Turn it off for a few days and the colony dies, and the maturing starts over.
That is a real electric bill, and one more reason a pond without fish is so much easier.
Clean it correctly
Rinse the pads in pond water, never tap water: chlorine and chloramine kill the bacteria you are trying to keep.
Rinse rather than scrub, and only when the flow clearly drops.
Replace UV bulbs every year or so; they stop working well long before they stop glowing.
Use plants over gear where you can
Submerged plants, lily pads and thick marginal planting outcompete algae for nutrients and shade the water. In a pond without fish, that is a complete solution.
Water and electricity are a deadly mix, and electrical codes have extra rules for pools, fountains and ponds. This is not an area to improvise.
✓The rules
Have any new outdoor circuit, outlet or buried cable installed by a licensed electrician to the National Electrical Code as your area adopts it (Article 680 covers pools and fountains). Many jurisdictions require a permit and inspection.
That includes any new outdoor outlet, a circuit to the yard, buried cable, and any hardwired pump, filter or lighting.
Every pump and outdoor outlet must be GFCI protected, and outdoor outlets need a weatherproof in-use (bubble) cover.
Every item must be rated for outdoor use, and for where it actually sits: near water, in the splash zone, or fully submerged.
Anything that goes underwater must be listed as submersible (look for a UL or ETL listing) for that use, not just "water resistant".
Never use an indoor extension cord, an indoor power strip or a homemade connection to reach a pond.
!Working safely around it
Unplug before your hands go in the water, every time: to clean a pump, clear an intake, plant, or fish something out.
Keep the transformer for any low-voltage gear out of the splash zone and off the ground, mounted as the maker says.
Use proper weatherproof connectors; tape and wire nuts fail outdoors within a season.
Route and record cords and cables so nobody puts a shovel through one later: along fixed edges, sketched and photographed.
Check cords, plugs and housings every year for damage, and replace rather than repair.
If a GFCI keeps tripping, something is wrong. Find out what, or have an electrician find out; do not keep resetting it.
Many small basin fountains run a low-voltage pump from a plug-in transformer, a simpler and safer setup. But the outdoor outlet the transformer plugs into still has to be a GFCI-protected outlet with an in-use cover, properly installed. Get that one thing right and most water features become easy. Solar pumps avoid wiring altogether for small features.
Making the decision
Which combination suits you
Find the row that matches your situation.
Choosing construction and equipment by situation.
If this is you
Choose
Why
Small children live at or visit the home
Basin fountain or wall spout, no pond
No open standing water at all
You want wildlife above everything
Fish-safe EPDM liner pond, no pump, no filter, no fish
Cheapest, lowest upkeep and by far the best habitat
You want sound in a small or paved space
Basin kit or wall spout
No digging, no pond, works on a patio
You want a pond fast and simply
Preformed shell, well installed
Quick, but the shape and shelves are fixed and installing it is fussier than it looks
Formal pool with crisp lines
Concrete block with an EPDM liner
Structure from the block, waterproofing from the liner
You want fish you can see clearly
Liner pond with a skimmer, solids-handling pump, filter and UV clarifier
The fish load is what makes filtration necessary
Rocky or root-filled ground
Preformed shell, or double underlayment under a liner
Puncture is the main threat to a liner
A waterfall or stream
Liner stream with a preformed top pool or waterfall box
Rigid top pool, flexible liner for the run
Trying water for the first time, little commitment
Container feature in a half barrel or stock tank
Roughly $75-$250, and it can be moved or drained
Avoid these
Six equipment mistakes
The first is about safety. The rest are why people spend more than they needed to.
1. Improvising the electrics
An indoor extension cord run out to the pond, an unrated light in the water, or a taped splice in a flower bed is a real shock hazard, and that is exactly why codes treat water features specially.
The fixHave any new circuit or outlet installed by a licensed electrician, use only outdoor and submersible-rated gear, plug everything into a GFCI-protected outlet, and unplug before your hands go in the water.
2. Buying a filter you do not need
Filters exist to deal with fish waste. A planted pond without fish balances itself, so a filter is just a purchase, an electric bill, a chore and one more thing to break, for no benefit.
The fixNo fish, no filter, no UV clarifier and no pump. Plant generously instead and let the pond settle.
3. Cheaping out on the liner
A cheap PVC or thin poly liner saves a little now and turns brittle within a few years in strong sun, and replacing a pond liner means draining and rebuilding the whole pond.
The fixBuy fish-safe 45 mil EPDM (or quality RPE) with a long warranty. It is the one part where saving money really is false economy.
4. Leaving out the underlayment
The most common cause of a leaking pond is a puncture from below, from a rock or root that was in the hole all along, and it usually shows up months later as a slowly falling level.
The fixClean the hole out completely, then lay proper pond underlayment over the whole area, up the sides and over the edges. Double it on rocky or root-filled ground.
5. Oversizing the pump
An oversized pump churns a small pond, stirs up muck, makes more noise than anyone wants and costs more to run all year.
The fixMatch the GPH to what the ornament or spillway actually needs, read the flow at your lift height rather than the headline figure, and choose a pump with an adjuster so you can turn it down.
6. Undersizing a fountain basin
A small basin under a bubbling fountain can run dry within days in summer heat, and a pump that runs dry burns out. That is the most common failure on these features.
The fixSize the basin generously, add an auto-fill valve or check the level often in hot weather, keep the pump reachable under a liftable grate, and set the feature so splash falls back on the stones.
Print it or tick as you go
The equipment checklist
Twelve things to confirm before you order. Your ticks are saved in this browser only.
Construction
Equipment
Electrical safety
Questions
Liners, pumps and equipment: your questions answered
Eight answers to the questions that come up most.
Should I use a flexible liner or a preformed pond?
A flexible liner for nearly any pond you plan to keep. Fish-safe EPDM lets you build any shape and size, including the sloping beach and varied depth a wildlife pond needs, lasts for decades, can be patched, and costs less per square foot once you go beyond a small pond. Preformed shells suit a small pond built fast, the top pool of a waterfall, or very rocky ground, but the shape and shelves are fixed, the shelves are usually narrow, and they are much harder to install well than they look.
What size pond liner do I need?
Liner length = pond length + (2 × maximum depth) + 2 ft of overlap, and the same formula for the width. So a pond 10 ft long, 6 ft wide and 2 ft deep needs roughly a 16 x 12 ft liner. Measure the largest dimensions of the finished hole, including any beach that extends outward, and round up to the next size sold: extra liner is simply trimmed, while a shortfall means starting over. Buy one piece rather than seaming sheets together.
Do I need underlayment under a pond liner?
Yes, and use real pond underlayment rather than a substitute. The most common cause of a leaking pond is a puncture from below, from a rock or root that was in the hole from the start, and it usually shows up months later as a slowly falling water level. Clean the hole out first, then lay a thick non-woven geotextile over the whole area, up the sides and over the edges. Use a double layer on rocky or root-filled ground, and put a second piece under any rock that sits on the liner.
Do I need a pump and filter in a backyard pond?
Only if you keep fish. Filters exist to deal with fish waste, so a planted pond without fish balances itself and needs no pump, filter, UV clarifier or electricity at all, which makes it the cheapest and easiest kind of pond. You need a pump if water has to move for a fountain, waterfall or stream, and filtration if the pond holds fish and you want water clear enough to see them. A small bubbler is worth considering where mosquitoes are a concern.
What size pond pump do I need (GPH)?
Size it to the feature, not just the pond. Small bubblers want roughly 100-250 gallons per hour (GPH); urns, bubbling rocks and wall spouts about 250-650; a waterfall about 100-150 GPH per inch of spillway width, so roughly 1,200-1,800 for a 12 in spillway; and a filtered fish pond should turn its whole volume over about once an hour. Always read the flow at your lift height rather than the headline figure, because pumps lose output as they lift. Pick one with a flow adjuster, and keep the tubing short and free of tight bends.
What does a UV clarifier actually do?
It does not filter anything. A UV clarifier runs water past an ultraviolet bulb, which makes free-floating algae clump together so the mechanical filter after it can catch them. That is why it clears green water, and why it is useless without a filter downstream. Replace the bulb about once a year, because it stops working well long before it stops glowing. In a planted pond without fish you do not need one: plants and shade do the same job for free.
Does a pond pump need a GFCI outlet?
Yes. Pond pumps, lights and de-icers should always be plugged into a GFCI-protected outdoor outlet with a weatherproof in-use cover, and every item must be rated for outdoor or submersible use where it sits. Electrical codes have extra rules for pools and fountains, so have any new circuit, outlet or buried cable installed by a licensed electrician; many jurisdictions require a permit. Never use an indoor extension cord, never keep resetting a GFCI that trips, and always unplug before your hands go in the water.
How long does a pond liner last?
Fish-safe 45 mil EPDM commonly lasts decades, and good liners carry a 20-year or longer warranty, which tells you what the maker thinks of them. PVC may manage only 5-10 years before sun makes it brittle, and cheap thin liner off a store roll even less. Since replacing a liner means draining and rebuilding the whole pond, this is the one part where saving money is false economy. Keep a patch kit with your pond paperwork, because punctures tend to happen years later.