Retaining Wall Problems: Leaning, Cracking, Bulging and What to Do
Retaining walls rarely fall over without warning. First the cap goes a little out of line, then the face leans, a crack opens after a hard winter, or water starts seeping where it never did. Each of those is the wall telling you something has changed behind it. Knowing what the signs mean, and which ones mean stop and call someone, is the most useful thing a homeowner with a retaining wall can know.
General guidance for US homeowners. A retaining wall that is leaning, bulging or cracking is a structural issue: keep weight off the ground above it, do not dig at its base, and have it assessed by a licensed engineer or an experienced contractor rather than patching it on a guess. Rebuilding a wall may need a permit, and you should call 811 before any digging. Part of the PlantMapper Retaining Walls section.
Most walls give plenty of warning before they fail · photograph via Pexels
How to think about it
Movement is information
Every retaining wall moves a little as it settles in during its first year or two. What matters is whether the movement is old and stable or current and getting worse, and you answer that by measuring and watching over time, not by looking once.
A wall that leaned 20 years ago, settled and has not moved since may be perfectly serviceable. The same lean, if it appeared over the last two winters and is still growing, is a wall on its way to failing.
The other thing to take on board is that almost every problem on this page is really a water problem. Water builds up behind the wall, the pressure rises (and in cold regions, the water freezes and heaves), and the wall responds by leaning, bulging or cracking. Fixing the face without fixing the water is why so many repaired walls fail again.
What to look for
The warning signs
Five things to check, and all of them take a few minutes with a 4 ft level, a tape measure and your phone camera.
Leaning or tilting
The clearest signal
Hold a long level against the face. A wall built with a deliberate setback leans back into the slope; a failing wall leans forward, out toward you.
Measure the lean at several points along the wall and write the numbers down with the date.
Check the cap or top course: it often goes visibly out of line before the face looks wrong.
A wall that has tipped from its base is a footing problem; one that has bowed in the middle is a pressure problem.
A forward lean that is increasing is the sign that most warrants advice right away.
Cracking
Read the pattern
Cracks tell you what kind of movement is happening. Their direction, width and whether they go right through matter more than how many there are.
Vertical cracks at intervals often point to bending or missing control joints.
Horizontal cracks, especially low down, suggest the wall is being pushed forward.
Stair-step cracks along mortar joints usually mean the footing has settled unevenly.
Measure the width, mark the ends with a pencil and the date, and photograph them.
Cracks that go right through, or that you can see daylight through, are serious.
Bulging
Pressure in the middle
A wall that is straight at the top and bottom but bellies out in the middle is being pushed by water or soil pressure it cannot resist. It is common in timber walls, gabions, segmental block built without enough geogrid, and thin brick walls.
Sight along the face from one end; a bulge is far easier to see than to measure.
A string line from end to end gives you a number you can repeat later.
On a gabion wall, check whether the baskets themselves are bulging, usually a lacing or bracing problem.
Bulging almost always means water. Check the weep holes and drain outlet first.
Water where there was none
The underlying cause
Changes in how water behaves around a wall are usually the earliest warning of all, and the one people ignore because it does not look structural.
Weep holes or a drain outlet that have stopped running, or that now run all the time.
Damp patches, staining, white efflorescence or moss spreading across the face.
Water seeping through joints instead of the weep holes.
Soft, soggy ground at the base of the wall after rain or snowmelt.
Puddles on the ground above the wall that used to drain away.
The ground around it
Look beyond the wall
The ground gives warnings the wall itself does not, and they are easy to miss because they look like ordinary yard wear.
Cracks, steps or dips appearing in the ground above the wall, running parallel to it.
A patio, steps or a path above the wall settling or tilting toward it.
Fence posts, a shed or a play set above the wall starting to lean.
Soil washing out through joints or weep holes, leaving a fan of silt at the base.
A gap opening between the wall and anything it butts against, such as steps or the house.
Working out what is wrong
Nine problems and their usual causes
Match the symptom to the likely cause. In almost every case, the first thing to check is whether water can get away from behind the wall.
Common retaining wall problems, their usual causes and the first thing to do.
Symptom
Most likely cause
What to do first
Wall leaning forward, getting worse
Water pressure behind the wall, or a footing too weak for the ground
Get it assessed. Keep weight off the ground above and do not dig at the base
Bulge in the middle of the wall
Water pressure from clogged or missing drainage; on block, too little geogrid
Check and clear weep holes and the drain outlet; have it assessed if the bulge is significant
Horizontal crack low down
The wall is being pushed forward and is bending
Treat as serious. Structural advice before anything else
Stair-step cracking along joints
Uneven settling of the footing
Monitor and photograph with dates; get advice if it is getting worse
Cap or top courses uneven after winter, blocks pushed out
Frost heave from water trapped behind or under the wall
Restore the drainage; get advice if movement repeats each winter
Weep holes or drain outlet have stopped running
Clogged with silt, roots or soil, or the drainage stone has clogged
Clear them; if they stay dry in a heavy rain, the drainage stone has failed
Soil washing out through joints or weep holes
Missing or torn filter fabric behind the wall
Stop the loss, then get advice; voids are forming behind the wall
Damp, staining and efflorescence on the face
Water is passing through the wall instead of around it
Check the drainage and weep holes; the face itself is only the symptom
Timbers soft or crumbling at the base
Rot (or termites) in the bottom course, where the wall stays wet
Assess how much of the wall is still doing its job; usually a rebuild
Before doing anything else, measure and photograph. Run a string line along the wall, record the lean at several points with a level, mark the ends of every crack with a pencil and the date, and take dated photos from fixed spots. Repeat in three months, and again after the winter. The difference tells you whether you have an old problem or an active one, and it is exactly what an engineer will want to see.
As an Amazon Associate, PlantMapper may earn from qualifying purchases. Prices and availability are set by Amazon. A forward lean with a horizontal crack low down needs a professional assessment now, not at the next check.
The serious cases
When to stop and get advice right away
Most retaining wall problems can be watched. A few should not be, and it is worth knowing which is which.
✓Act now: get a structural assessment
The wall is leaning forward and the lean is visibly increasing.
A horizontal crack has opened, especially low in the wall.
The wall has bulged significantly, or any part has moved suddenly.
Soil or water is coming through the wall and voids are forming behind it.
The ground above the wall has cracked, stepped or dropped.
Something above the wall (a shed, a patio, a driveway, a building) is moving.
The wall supports or is close to the house, garage or an addition.
A neighbor's yard, wall, fence or house is affected.
!Meanwhile, do not
Add any weight to the ground above: no parking, no piles of mulch or pavers, no new patio.
Dig at the base of the wall or remove anything bracing it.
Run sprinklers above it, or let a leaking pipe or downspout drain behind it.
Simply patch or stucco over the cracks; that hides the evidence without changing the cause.
Let people walk near the top or the base of a wall that is actively moving; keep kids and pets away.
Remove a tree or big shrub near the wall without advice; on clay, that changes soil moisture and can make things worse.
If a moving wall holds up, or is held up by, land you do not own, tell your neighbor and get advice early. These situations get expensive and complicated quickly, and an engineer's report obtained before anything collapses is far more useful than one obtained afterward. It is also worth checking your homeowners policy, since many standard policies exclude earth movement.
The underlying cause
Drainage failure
If you only ever check one thing on a retaining wall, check whether water can still get away from behind it. Lost drainage is what turns a sound wall into a failing one, usually years after it was built.
Watch the wall in a heavy rain
Go out while it is pouring and look at the weep holes and the end of the drain pipe. On a wall with working drainage, water runs from them during and after a heavy rain, often with staining or green growth below. That is a wall doing its job.
Outlets that stay bone dry through a downpour, on a wall that used to run, are the clearest sign that the drainage has clogged.
Clear the weep holes
They clog with silt, moss, soil, leaves and sometimes wasp or mud dauber nests, and clearing them is a five-minute job with a length of stiff wire or a thin rod.
Do not force anything deep into the wall; you can push the filter fabric out of place or start soil washing through. Clear the opening, then watch what happens in the next storm.
Find where the drain pipe comes out
Look for the outlet at the end of the wall or downslope from it. A drain pipe with a clogged, buried or crushed outlet is not a drain. Roots and critters often block the open end; a simple grate or critter guard helps.
Clear the outlet and the gravel or swale it drains into. If you cannot find an outlet at all, that may be the whole problem.
Look at what is coming from above
A wall across a slope receives everything the ground above sheds. A new patio, a shed roof, an addition, a moved downspout, a sprinkler zone or a clogged drain above the wall can put far more water behind it than it was built for.
Catch it before it gets there: a swale, a shallow gravel trench or a channel drain across the slope above, and make sure any hard surface above slopes away from the wall, not toward it.
Suspect a leak if the ground stays wet in dry weather
Soil that stays wet behind or below a wall when it has not rained points to a leaking water line, an irrigation leak, a broken drain line or a dry well emptying into the soil behind the wall.
Getting that traced and fixed is often the single most effective thing you can do for the wall.
Know when the drainage stone itself has failed
If the weep holes and outlet are clear and the wall is still wet and moving, the drainage stone behind it has probably silted up, usually because there was no filter fabric.
That cannot be fixed from the front. It means digging out behind the wall and rebuilding the drainage, which is contractor work and usually worth an engineer's advice first.
Water that cannot get away is behind almost every failed retaining wallWatch the weep holes in a heavy rain: running is good, bone dry is notFree-draining walls sidestep the problem that destroys most others
Keeping it sound
Maintenance
A sound retaining wall needs very little, but the little it needs is about drainage, and it almost never gets done. Twenty minutes twice a year is the whole routine.
Twice a year, twenty minutes
Clear the weep holes of silt, moss, soil and leaves, in spring and fall.
Find and clear the drain pipe outlet and whatever it drains into.
Walk the wall in a heavy rain at least once a year and watch what the outlets do.
Check the cap: cracked, loose or missing caps let water straight into the top of
the wall.
Look at the ground above for new cracks, dips or a patio starting to tilt toward
the wall.
Sight along the face for any new lean or bulge, especially after winter, and
compare with your photos.
Segmental block, mortar joints and stucco
On segmental block, reglue loose caps with exterior masonry adhesive, and reset any
block that has shifted before the course above moves.
Repoint failed mortar joints before water gets behind them, using a mortar suited to the
masonry; very hard cement mortar damages softer stone and older brick.
Repair cracked or flaking stucco promptly; water behind stucco pops it off in sheets.
Do not patch or stucco over a crack you have not understood. Cover the evidence and you
lose the ability to monitor it.
Clean algae and moss off the face with a stiff brush and water. Avoid blasting a pressure
washer at the joints, which strips out mortar and joint sand.
Keep clinging vines such as English ivy off mortared walls; they work into the joints and
hold moisture against the masonry.
Timber walls
The bottom course fails first, because it sits in damp soil. Probe it with a
screwdriver once a year; soft wood means rot. In the South, look for termite mud tubes too.
Seal any fresh cut right away with end-cut preservative; an oil or stain on the face is
optional.
Check the screws or spikes between courses, and any posts or deadmen, for rust and
looseness.
Keep soil, mulch and plants off the front face and back from the top, where they trap
moisture.
Expect roughly 10 to 20 years from a ground-contact treated wall. Plan the replacement
instead of being surprised by it.
Gabion and dry-laid stone walls
Gabions: check the wire for rust, especially at cut ends, ties and near the
ground, and check the lacing and internal bracing wires.
Top up settled stone at the top of a basket; the fill packs down over the first few
years.
Look for soil washing out through the face, which means the filter fabric has failed or
was never fitted.
Dry-laid stone and boulders: reset stones that have worked loose promptly, before
the course above starts to move, and check after frost and heavy rain.
Keep woody growth out of a stone face; small plants are fine and welcome, self-sown trees
and shrubs are not.
A bulging dry-laid wall usually means the stone packed behind the face has settled;
that is a job for an experienced stone mason, not a patch.
Putting things right
Repairs, and what they can and cannot do
Some retaining wall repairs are real fixes. Others are cosmetic, and it matters to know which is which before you spend money.
✓Repairs that genuinely help
Restoring the drainage. Clearing weep holes and the drain outlet, and diverting water coming from above. Often the single most effective thing you can do.
Repointing and fixing the cap, which stops water getting into the top and the joints.
Replacing failed filter fabric and drainage stone: a real repair, but it means digging out behind the wall.
Taking weight off the top: removing stored material, a shed or extra fill, or regrading the ground above.
Rebuilding a section of a segmental block, timber, gabion or dry-laid stone wall, all of which can be rebuilt in sections.
Fixing a leak: a broken water or irrigation line, a cracked drain or a dry well emptying behind the wall.
!Repairs that only look like fixes
Patching or stuccoing over cracks in a wall that is still moving. The crack comes back, and in the meantime you cannot monitor it.
Drilling weep holes in a wall with no drainage stone behind it; there is nothing for them to drain.
Bracing or propping a leaning wall without understanding why it leans.
Trying to push a bulged wall back, which does not work and is dangerous to attempt.
Piling soil against the front to hold it up; it does very little and hides the base from inspection.
Rebuilding the face of a failed wall while leaving the original drainage and backfill in place. It will fail again.
The honest position on a wall that has truly failed is that rebuilding it properly usually costs less than repairing it twice. A rebuild lets you put in the drainage stone, filter fabric and compacted backfill that were missing, which is what caused the failure in the first place, and it is the point at which an engineer's design is a small fraction of the job. A rebuild of a taller wall will often need a permit, so check with your building department.
A wall you did not build
Retaining walls that came with the house
Most people meet a retaining wall by buying a house with one. You have no idea how it was built, and the face tells you almost nothing.
Find out who owns it and who is responsible
Check your deed, plat and property survey, and any HOA documents, which sometimes make the HOA responsible for walls in common areas. Where a wall holds up a neighbor's yard, or theirs holds up yours, responsibility can be a legal question, and it is worth clarifying before anything happens rather than after.
If your home inspection or the seller's disclosure mentioned the wall, dig out what it said.
Assume nothing about the drainage
Older retaining walls often have no drainage stone, no filter fabric and no drain pipe. Some have weep holes with nothing behind them.
Watch the wall in a heavy rain. Running weep holes are a good sign; a wall that is damp all over and never weeps probably has nothing behind it.
Record its condition now
Photograph the whole wall from fixed spots, measure the lean at several points, mark and date every crack, and run a string line along the face to record any bulge.
That baseline is worth a great deal later, both for your own peace of mind and for any professional you eventually call.
Do not make it work harder
The most common way people damage an inherited wall is by changing what is above it: a new patio, parking, a shed, a hot tub, raised beds, or a moved downspout.
Any of those adds weight or water. If you are planning work above a retaining wall of unknown construction, get advice first.
Get it assessed if anything is moving
An old, stable lean on a wall that has not moved in years may be fine. Anything that is moving now should be looked at by a licensed engineer.
A short assessment typically costs a few hundred dollars. It is also exactly the document you will want when you sell, or if a neighbor raises the wall as an issue.
The routine
A retaining wall through the year
Two short inspections and one wet-weather walk are really all a sound wall asks for. Shift the timing to your climate: spring comes in February in the Deep South and May in the northern tier, and in the West the walk in the rain belongs to whenever your rainy season is.
Spring
Once the ground has thawed
The main inspection, after winter has done its worst.
Clear the weep holes and the drain outlet.
Sight along the face and compare with last year's photos; look for frost movement.
Check the cap for cracked, loose or missing pieces and fix them promptly.
Repoint failed joints once nights are reliably above freezing.
Probe the bottom course of a timber wall for rot.
Summer
The building season
The window for repairs and rebuilding, and for keeping growth in check.
Do any repointing, stucco repair or rebuilding now, avoiding the hottest midday sun, which dries mortar too fast.
Cut back clinging vines and any woody growth in a stone or gabion face.
Re-stain timber walls if you choose to.
Keep plants and mulch off the face and back from the top edge.
Check nothing new and heavy has ended up on the ground above.
Fall
Before the wet season or the freeze
The most important season, because it sets the wall up for the wet, cold months.
Clear the weep holes again, and the outlet, before winter rain and snow.
Clear fallen leaves from any gravel strip or channel at the base.
Walk the wall during the first real storm and watch what the outlets do.
Check the ground above for new cracks, dips or a tilting patio.
Shut off and drain any irrigation above the wall before the freeze, and photograph the wall from your fixed spots.
Winter
Watching season
Very little work is possible or wise, and this is when problems show themselves.
Look at the wall after heavy rain, a thaw or snowmelt, when pressure is highest.
Watch for new damp patches, seepage through joints, ice on the face or soil washing out.
Do not pile plowed or shoveled snow against or on top of the wall.
Avoid mortar work and stucco in freezing weather, and keep weight off soggy ground above.
Note anything that has changed for the spring inspection.
Avoid these
Six mistakes with an existing wall
How people turn a serviceable retaining wall into a failing one, or a failing one into a collapsed one.
1. Changing what is above the wall
A new patio, parking, a shed, a hot tub or raised beds above an existing wall adds load it was never built for. This is by far the most common way an inherited wall gets pushed into failure.
The fixGet advice before adding any weight above a retaining wall, especially one of unknown construction. Vehicles and buildings above a wall need a licensed engineer, no exceptions.
2. Digging at the base
Cutting a bed, laying a path, digging a dry well or lowering the ground at the foot of a wall removes exactly the soil that holds its base in place.
The fixDo not dig at the base of a retaining wall. If work there cannot be avoided, get it designed, call 811 first, and take extra care near a neighbor's property.
3. Patching over the evidence
Filling cracks in a wall that is still moving hides the one thing that would have told you whether the movement is getting worse, and changes nothing about the cause.
The fixMeasure, mark, date and photograph first. Watch for at least a season, including a winter in cold regions, before deciding whether the movement is old or active, then fix the cause, not the crack.
4. Ignoring the weep holes
Weep holes are the cheapest maintenance in the yard and the most consistently forgotten. Once they clog, water builds up behind the wall and the pressure it was built to avoid arrives anyway.
The fixClear them twice a year, find and clear the drain outlet, and go out in a heavy rain once a year to check they actually run.
5. Planting a tree near the wall, or cutting one down
Roots push and change how wet the soil behind the wall is. On clay, especially expansive clay, both planting and removing a big tree near a wall change soil movement significantly.
The fixKeep trees and vigorous shrubs well away from retaining walls, and get an arborist's and an engineer's advice before removing an established tree close to one.
6. Rebuilding the face and leaving the rest
A wall that failed because of water will fail again if you rebuild the visible part and leave the original backfill, missing fabric and clogged drainage behind it.
The fixIf a wall has truly failed, rebuild it properly: drainage stone, filter fabric, a drain pipe with a real outlet, and compacted granular backfill. That is when an engineer's design is a small part of the cost.
Print or tick as you go
The inspection and maintenance checklist
Fourteen checks across the year. Your ticks are saved in this browser only.
Inspection
Drainage
Care and caution
Questions
Retaining wall problems: your questions answered
Eight answers to the questions that come up most.
My retaining wall is leaning. Is it dangerous?
It depends on whether the lean is old and stable or new and getting worse, and the way to tell is to measure rather than eyeball it. Hold a level against the face at several points, write the readings down with the date, mark and date the ends of any cracks, take photos from the same spots, and repeat in three months. A lean that has not changed in years may be fine; a lean that is clearly increasing, or any forward lean with a horizontal crack low down, should be looked at by a licensed engineer right away. Meanwhile keep weight off the ground above and do not dig at the base.
What do cracks in a retaining wall mean?
The pattern tells you what kind of movement is happening. Vertical cracks at intervals often point to bending or missing control joints. Horizontal cracks, especially low down, suggest the wall is being pushed forward and are the most worrying. Stair-step cracks along mortar joints usually mean the footing has settled unevenly. Cracks that go right through the wall are serious in any pattern. Measure the width, mark and date the ends, photograph them and keep watching; do not patch over them, because that hides whether they are still moving.
Why is my retaining wall bulging in the middle?
Almost always water. A wall that is straight at the top and bottom but bellies out in the middle is being pushed by water pressure from saturated soil behind it, which means the drainage has clogged or was never there. Check the weep holes and drain outlet first, ideally during a heavy rain: if they stay dry in a downpour, that is your answer. On segmental block, a bulge can also mean missing or too-short geogrid; on a gabion wall it is usually a lacing or bracing problem. A significant bulge should be assessed, and a bulged wall cannot simply be pushed back.
Can frost heave damage a retaining wall?
Yes, in any region with freezing winters. Water trapped in the soil behind or under a wall freezes and expands, pushing the wall out or lifting the footing, and the movement often ratchets a little further each winter. Signs include a cap or top course that is uneven after winter, blocks or timbers pushed forward, and cracks that open in late winter. The cure is the same as for most wall problems: get water away from the wall with clean drainage stone and a working drain, and make sure rigid footings are below the local frost line.
How do I know if the drainage behind my wall has failed?
Go out during a heavy rain and look. A wall with working drainage runs water from its weep holes or drain outlet during and after a downpour, often with a dark stain or green growth below. Outlets that stay bone dry in a downpour, on a wall that used to run, have clogged. Clear them with stiff wire, find and clear the drain pipe outlet, and watch again. If everything is clear but the wall is still wet and moving, the drainage stone behind it has probably silted up, usually because there was no filter fabric, and that can only be fixed from behind.
Can I fix a leaning retaining wall myself?
You can restore the drainage, clear weep holes and outlets, divert water coming from above, repoint failed joints, reglue loose caps, and on segmental block, timber, gabion or dry-laid stone walls you can rebuild a short section. What you should not do is prop, brace, push back or patch over a wall that is actively moving, because none of those fixes the cause and some are dangerous. A wall that keeps leaning needs a licensed engineer or an experienced contractor to work out why before anyone repairs it.
I have a retaining wall that came with the house. What should I do?
Three things. Find out who owns it and who is responsible, using your deed, plat or property survey, especially if it holds up a neighbor's yard or theirs holds up yours; check HOA documents too. Record its condition now: photos from fixed spots, lean measured at several points, cracks marked and dated, a string line along the face. And assume nothing about the drainage, because many older walls have none. Above all, do not make it work harder by adding a patio, parking, a shed or raised beds above it without advice.
Is it cheaper to repair or rebuild a failed retaining wall?
If the wall has truly failed, rather than just needing its drainage restored, rebuilding it properly is usually cheaper than repairing it twice. The failure was almost certainly caused by what is behind the wall: no drainage stone, no filter fabric, loose backfill or a weak base. Rebuilding the face and leaving those in place produces a wall that fails again. A rebuild lets you fix the cause, and that is when an engineer's design is a small part of the total cost. Note that many standard homeowners policies exclude earth movement, so check your coverage before assuming insurance will pay.