Landscape Edging · Care

Landscape Edging Maintenance and Repair

Good edging is close to set-and-forget, but not quite. Winter frost nudges it up, summer heat makes plastic wander, and Bermudagrass is always looking for a way over the top. Catch one lifted piece in spring and it is a two-minute fix; ignore it and by fall the whole run is wavy. Here is the yearly routine, care for each material, the eight problems you are likely to see and the point where replacing beats repairing.

General guidance for American yards. If an edge that also holds back soil or a slope has shifted, get advice before you dig it out, and call 811 before driving new stakes deeper than the old ones. Part of the PlantMapper Landscape Edging section.

A brick patio with a table and chairs set against an old stone wall
Brick ages gracefully; it is the mortar and the base that wear out first · photograph via Pexels
What to expect

Thirty minutes a year, timed right

Most edging really does look after itself. The trouble is that small movements snowball. One stake loosens over the winter, that section rises a little, the mower clips it, it rises further, and a couple of seasons later sixty feet of edge is wandering instead of one board.

The cure is a single walk along every edge each spring, as soon as the ground has thawed and before new growth hides the line, carrying a rubber mallet and a few spare stakes. Tap down anything proud, restake anything loose, and trim back grass that has crept over. For steel, aluminum, composite, wood and precast concrete, that really is the whole job.

How much work you get depends on where you live. In the North and the Mountain West, frost heave is the main enemy and spring is when you see the damage. In the South, there is little frost, but warm-season grasses like Bermudagrass, zoysia and St. Augustine creep relentlessly all summer. Brick, pavers and stone ask for a little more: the joints and base give out long before the material, so expect to reset the odd piece every decade.

The whole routine

Edging care through the year

Timing follows your climate, not the calendar. Two moments matter; the rest is as-you-notice. Find your growing zone if you are not sure which applies.

A year-round routine for landscape edging, timed by season and zone.
WhenWhat to doHow long
Early spring, once the ground thaws (about March in zones 6-7, April to May in zones 3-5, late winter in zones 8-10)The main check. Walk every run with a mallet. Tap down anything frost has lifted, drive new stakes where old ones are loose, note anything that has drifted20-30 minutes
Spring, as the lawn greens upTrim grass that has grown over a flush edge; sweep soil, mulch and winter grit off a mow stripHalf an hour
Through the mowing seasonNothing scheduled. Push down anything the mower catches when you notice itMinutes
Mid to late summerCut back Bermudagrass, zoysia or St. Augustine runners going over or under the edge into beds - every few weeks in the South15 minutes
FallRake leaves away from the edge, especially off a mow strip where they stain and grow moss; check stakes before the ground freezes15 minutes
Winter (cold zones)Keep snowblowers and plow blades off edging along walks and driveways; use sand or calcium magnesium acetate instead of rock salt next to metal and concrete edging where you canNone
Every 5-10 yearsReset or repoint the odd brick, paver or stone; replace any wood board that has gone soft; reseal colored concrete curbingA morning
Whenever it needs itRecut a spade-cut edge with a half-moon edger - two or three times a season if you have no hard edging20 minutes a session

Do the main check as soon as the ground thaws. Every edge is visible, the soil is soft enough to drive a stake without a fight, frost damage from the winter is plain to see, and anything you fix is solid before mowing starts. Doing it in July through a full flower bed takes three times as long and you miss half of it.

What each one needs

Care by material

Brief, because most of these need very little.

Steel and aluminum

The lowest-maintenance edging you can buy. Little to do beyond the spring walk-around.

  • Spring check Tap down any section that frost has raised and drive a new stake beside it
  • Weathering steel keeps developing its rusty patina for two or three years, then settles down. Expect some orange staining on light concrete or pavers next to it in the first year
  • Powder-coated or galvanized steel may show surface rust at cut ends and scratches. It is cosmetic; touch up visible spots with rust-inhibiting paint if it bothers you
  • Salt and the coast speed up rust. Rinse edging beside salted walks with the hose in spring; in coastal yards, aluminum is the better replacement
  • Watch the joints - a connection that has pulled apart is the one thing worth fixing right away

Wood boards and landscape timbers

Needs less attention than a deck or fence, because it is small and cheap to replace.

  • Spring check Push a screwdriver into the ends and the buried edge. Soft wood at the ends is the usual first sign of rot
  • Drive new stakes where old ones have loosened, and replace any stake that has rotted at ground level
  • Don't bother re-treating the faces. The protection in pressure-treated lumber is inside the wood; surface coats do little on buried wood
  • Seal cut ends with end-cut preservative whenever you cut a replacement piece
  • Expect about 7-10 years from a board (longer in the dry West, shorter in the humid Southeast), and replace boards one at a time as they go

Brick, pavers, stone and concrete

The material lasts for decades. The joints, the base and the restraint behind it don't.

  • Resetting and repointing is the whole job. On mortared edging, rake a failed joint out about 1/2 inch deep and repoint with a premixed mortar; on dry-laid pavers, lift and reset any piece that has sunk or tipped
  • Moss and algae make a mow strip slippery in damp shade. Scrub it off in fall, with a patio and masonry cleaner if it is heavy
  • A loose or rocking piece means the base or the concrete haunch behind it has failed. Lift it, reset it and support it properly - don't just stamp it back down
  • Flaking brick faces mean the brick wasn't rated for freeze-thaw. Replace those pieces with paving brick or pavers
  • Concrete curbing cracks where frost or roots lift it. Hairline cracks are cosmetic; reseal colored or stamped curbing every few years so it keeps its color
  • Keep soil and mulch off a mow strip, or it stops being one

Roll plastic and composite

Composite needs nothing. Thin roll plastic needs more attention than any other edging, which is worth knowing before you buy it.

  • Roll plastic: expect to push it back down every spring. Summer heat and winter frost both lift it, and once one section is proud the rest follows
  • Roll plastic: add stakes instead of fighting the same section over and over - one every 12 inches usually settles it
  • Roll plastic turns brittle after about five years in strong sun and then cracks when tapped. That is the end of its life
  • Composite: a spring look and nothing else. It does not rot, fade much or need treating
  • Never oil, stain or paint composite - it cannot absorb it
The free option

Keeping a spade-cut edge sharp

Not every bed needs a product. A clean spade-cut edge (sometimes called a natural or English edge) costs nothing, follows any curve, and done well it looks better than most plastic on the shelf. It just has to be redone.

  1. Cut it in spring with a half-moon edger

    A flat-bladed half-moon edger gives a clean straight face where a round shovel gives a scalloped one. Work backward along the line so you never stand on the edge you have just cut. A powered bed edger does the same job faster on long runs.

  2. Use a board or a garden hose as a guide

    A straight 2x4 for straight runs, a garden hose for curves. Edging by eye drifts, and it drifts a little further each year until the bed has changed shape.

  3. Cut a straight face and a small trench

    A clean vertical cut on the lawn side, about 3-4 inches deep, and 2 inches or so of bare soil sloping back into the bed. That little trench is what stops grass runners crossing.

  4. Remove the trimmings

    Sod pieces left in the bed root and grow, especially Bermudagrass. Pick them up and compost them or put them in the yard waste.

  5. Touch it up through the season

    A string trimmer turned on its side, an edging shear or a stick edger every few weeks keeps the line crisp between full recuts.

  6. Know the trade you are making

    A cut edge is free and looks great but needs doing a few times a season, forever. Hard edging costs money once and then mostly leaves you alone. Neither is wrong - just know which deal you are choosing. With Bermudagrass or zoysia, a hard edge usually wins.

Edging tools

Amazon picks

As an Amazon Associate, PlantMapper may earn from qualifying purchases. Prices and availability are set by Amazon. A spade-cut edge is a perfectly good free option - it just needs recutting each spring and touching up through the season.

Diagnosis

Eight edging problems and what causes them

Nearly everything that goes wrong with landscape edging is in this table.

Common landscape edging problems, their usual cause and the practical fix.
What you seeUsually meansWhat to do
A section standing higher than the rest after winterFrost heave, or a stake that has loosened, rotted or was only ever in loose backfillTap the section down and drive a new, longer stake beside the old one into firm soil below the trench - below the frost-active layer where you can
Roll plastic rising in a wavy lineHeat expansion in summer and frost heave in winter ratchet it upwardAdd stakes every 12 inches and bury more of its depth. If it has turned brittle, replace it
Metal edging rippling along its lengthGauge too light, or it was hammered on the top edge instead of through the stakesRipples won't press out. Replace those lengths with 14-gauge steel or heavier, or aluminum
A gap opening at a jointPieces butted instead of overlapped, or the connector has worked loosePull the pieces back together, overlap or connect them as the maker intends and restake at the joint
Grass creeping into the bedThe edge is too shallow or too low; Bermudagrass and zoysia also travel over the top by runnersDig out the runners in the bed. If it happens every year, replace with edging buried 4-6 inches and standing about 1/2 inch above the soil, and trim runners regularly
A brick, paver or stone row tipping outwardNo concrete haunch or restraint behind it, or the base has washed out or heavedLift the affected pieces, reset them on a firm base and support them with a concrete haunch kept below the finished soil
Wood gone soft at the endsUnsealed cut ends, which soak up water from day oneReplace that board, sealing the cut ends of the new one before it goes in
A new puddle on one side of the edgingThe edge is damming water that used to flow across the lineGive it a way through: remove a short section, open a joint, or swap part of the run for a permeable edge such as dry-laid stone
Fixing it

The four repairs worth knowing

Between them, these cover nearly everything an edge will ever need.

  1. Resetting a frost-lifted section

    Tap the section back to the right height, with a scrap of wood on top to protect it. Then drive a new stake beside the old one rather than pounding the old one back in - its hole is enlarged and won't hold. In cold zones use a longer stake (12 to 18 inches) so it reaches firm soil well below the trench; the deeper it goes, the less frost can grip it.

  2. Replacing one wood board

    Cut through the old board on either side of the rot with a handsaw instead of fighting the fasteners. Check the stakes while it is out and replace any that are soft at soil level. Cut the new ground-contact board to length, seal every cut end, and land the joints on a stake so both boards share it. Use exterior-rated screws or galvanized nails.

  3. Repointing a mortared brick or stone edge

    Rake out the failed joint about 1/2 inch deep with a joint raker or an old screwdriver, brush it clean and dampen it. Pack in a stiff premixed mortar, press it in well and strike it off flush. Keep it damp for a day or two in hot weather so it cures instead of drying out, and don't repoint when frost is expected within a couple of days.

  4. Resetting a rocking piece

    Lift the loose brick, paver, cobble or curb piece right out. Clean off the old mortar or loose base, refill and tamp the base, then reset it to a string line and support the back with a concrete haunch kept below the finished soil. Pushing a loose piece back without fixing what is underneath just repeats the failure.

The judgment call

Repair or replace?

A quick test for each situation.

✓Repair it

  • A few lifted sections on an otherwise straight run - a new stake fixes each in two minutes.
  • One or two soft wood boards in a run where the rest is sound.
  • A failed mortar joint or a single rocking piece in brick, pavers or stone.
  • A separated joint in metal or composite.
  • Hairline cracks in concrete curbing that is still level.
  • Grass creeping in where the edging itself is still true - that is a weeding job, not an edging job.

!Replace it

  • Rippled or kinked metal. The damage is permanent and will always show.
  • Roll plastic that has turned brittle and cracks when you tap it - usually after five to eight years.
  • Wood soft along its length, not just at the ends.
  • An edge that fails the same way every spring, which means it was installed wrong rather than worn out - usually too shallow or staked into loose soil.
  • Curbing broken into heaved, tilted chunks by frost or tree roots.
  • Any edge you fight more than once a year. Your time is worth more than the material.

When you replace, fix the cause. Edging that fails early almost always failed for a reason that is still there: stakes in loose backfill, no base or haunch, light-gauge metal, unsealed cut ends, an edge too shallow for frost or for Bermudagrass, or an edge asked to hold back soil it was never built for. Put the same product back the same way and you get the same short life. Spend an extra twenty minutes doing the installation properly and the new edge will outlast the old one several times over.

Learn from other yards

Six maintenance mistakes

1. Ignoring one lifted section

It snags the mower, the mower pushes it further, and within two seasons the whole run is wandering.

The fixDeal with a raised section the week you spot it. At that stage it is a two-minute job.

2. Pounding the old stake back in

The hole it pulled out of is enlarged, so it works loose again within months - often by the next thaw.

The fixDrive a new, longer stake beside it into firm soil below the trench.

3. Stamping a rocking paver back down

The problem is the base or the support behind it, not the paver, so it rocks again by next spring.

The fixLift it, rebuild the base, reset it and support it properly.

4. Letting soil and mulch bury a mow strip

A strip covered in mulch or soil isn't a mow strip any more, and grass roots straight into the covering.

The fixSweep it clear in spring and fall, and keep bed soil and mulch about 1 1/2 to 2 inches below its top.

5. Rock salt and snowblowers along metal edging

Salt speeds up rust on steel and pits concrete curbing, and an auger or plow blade can bend a whole run along a driveway or walk.

The fixMark edging with snow stakes before winter, use sand or a gentler de-icer near it, and choose aluminum or stone where salt is unavoidable.

6. Replacing failed edging exactly as it was

If it failed because it was understaked, too shallow or had no base, the new one fails the same way on the same timeline.

The fixWork out why it failed before buying the replacement, and correct the installation.

Once a year

The spring edging check

Twelve checks, about half an hour. Ticks are saved in this browser only.

Walk the run

Material checks

Around the edge

Care questions

Landscape edging maintenance: frequently asked questions

Why does my plastic edging keep popping up?

Two forces work on it. Thin plastic expands in summer sun and shrinks at night, and in colder zones frost heave pushes it up every winter, so each cycle ratchets it a little further out of the ground until the run is wavy. The fix is more stakes - roughly one every 12 inches, about twice what the box suggests - and burying at least two thirds of its depth. If it has turned brittle and cracks when tapped, it is worn out and needs replacing.

How do I stop Bermudagrass from growing over my edging?

Bermudagrass and zoysia spread both by underground rhizomes and by above-ground runners, so the edge has to block both: bury it 4 to 6 inches deep and leave it standing about 1/2 inch above the soil so runners can't simply step over. Then trim the runners that reach the edge every few weeks in summer, and dig out any that have rooted in the bed rather than just pulling the tops. Steel, aluminum and concrete curbing hold up best; thin plastic and loose stone let it through.

How do I fix edging that frost has pushed up?

Wait until the ground has fully thawed, then tap the section back down with a rubber mallet and a block of wood. Drive a new, longer stake beside the old one into firm soil below the trench, rather than reusing the loosened hole. If the same run heaves every winter, it is too shallow or sitting in poorly drained soil: reinstall it deeper, on a few inches of compacted gravel, so water drains away from it instead of freezing around it.

How often should a spade-cut lawn edge be redone?

Cut it properly with a half-moon edger once in spring, then touch it up with edging shears or a string trimmer every few weeks through the mowing season. In the South, where Bermudagrass and St. Augustine grow fast, that may mean a full recut two or three times a year. That is the trade with a cut edge: it is free and looks great, but it asks for that time forever, where hard edging asks once.

Can I fix rusty steel edging?

Usually there is nothing to fix. Weathering steel is meant to rust and stabilizes after two or three years, and surface rust on cut ends of coated steel is cosmetic. What can't be repaired is a rippled or kinked section, or steel that has rusted through near the coast or beside a salted walk - replace those lengths, ideally with heavier steel or with aluminum, which doesn't rust.

My brick or paver edging is coming loose. What should I do?

A rocking brick or paver almost always means the base underneath has washed out or heaved, or the concrete haunch or restraint behind it has failed or was never there. Lift the loose pieces completely, clean off old mortar, refill and tamp the base, reset them to a string line, and support the back with concrete kept below the finished soil. Pressing them back down without fixing the support just repeats the problem.

Should I treat wood edging every year?

No. The preservative in pressure-treated lumber is inside the wood, and a surface coat on a board buried on one face and its bottom edge does very little. What matters is sealing every cut end with end-cut preservative when you cut it, because that is where water gets in. Expect about seven to ten years from a board, longer in dry climates, and replace boards individually as they go.

How do I know when edging needs replacing instead of repairing?

Repair isolated faults: a lifted section, one soft board, a failed mortar joint, a separated connector. Replace when the failure is built in - metal that has rippled, plastic that has turned brittle, wood soft along its whole length, curbing broken into heaved chunks, or an edge that frost lifts in the same place every spring. The other signal is time: if you are fixing the same edge more than once a year, replacing it costs less than your weekends.

Puddles have appeared since I installed edging. Why?

A solid run of edging across a slope acts as a small dam, stopping water that used to sheet across the line, so it collects on the uphill side. Give the water a route: remove a short section at the low point, open a joint or two in a brick or stone run, or replace part of the line with a permeable edge such as dry-laid stone. If the whole area stays soggy, see Yard Drainage.

Where to go from here

Next steps